High Heat “Futura” fiber has been in the instustry for many years now. The advantage of high heat fiber is that you can have all of the great benefits of human hair, without the cost. Some challenges can be tangling, frizzing, and resistance to styling. But what makes Jon Renau and easihair’s “HD” heat defiant fiber different? We worked for 2 years creating and designing the styles of our collection of HD wigs and extensions, featuring the second generation fiber “Futura ST”. We are proud to offer the most natural movement and texture of any synthetic fiber on the market. With proper care and maintenance, you can have the power to reinvent your look every day!

Jon Renau HD Smooth is a specially formulated product to help maintain and detangle your HD wigs and extensions. It is especially important to use this in the areas the fiber comes in contact with the body, (ends, nape area, etc.) Simply mist throughout the lower lengths and ends of the fiber and gently comb with your Jon Renau Wide Tooth Comb before and after wearing. Works great on synthetic fiber products too!

Wash- Before washing your HD wig, gently remove any tangles with your Jon Renau wide tooth comb only. Fill sink with cool water and submerge wig. Emulsify a capful of Jon Renau Synthetic Wig Shampoo into the wig. Gently lather the hair with shampoo, while making sure that the hair is traveling in the same direction. DO NOT rub hair as this may cause tangling. Rinse thoroughly with cool water until water runs clear.

Dry- Wrap wig in a towel and gently pat dry. Gently detangle hair using your Jon Renau wide tooth comb. Spray with Jon Renau Leave-in Conditioning Spray (3-5 pumps) keeping away from base of wig. Apply Jon Renau HD smooth detangling spray, (3-5 pumps) focusing on the bottom half of wig. Gently comb through again with your Jon Renau wide tooth comb. Air drying your wig will give the best results. You can gently blow dry (low-medium heat) using ONLY your Jon Renau wide tooth comb.

Style- We recommend that ONLY the Jon Renau wide tooth comb is used on your HD wig. Other tools will cause frizzing/tangling. HD Fiber can withstand heat tools up to 350 degrees farenhieght, however, Jon Renau recommends working at 270-280 degrees fairenheight. It is recommended to use professional grade heat styling tools with digital temperature settings to control heat. We recommend using Jon Renau HD Smooth with a Jon Renau wide tooth comb DAILY to detangle your HD wig. This is especially important with the mid-length to long length HD wigs.

 

Curl- Heat your curling iron to 270 to 280 degrees fairenghit. Using a wide tooth comb, gently comb hair free of tangles. Starting at the nape, take 1/2 inch to 1 1/2 inch sections of hair (smaller sections= tighter curls, larger sections=looser curls). Spray with Jon Renau Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section). Gather hair into curling iron, smooth through to the ends. Roll iron up towards base of wig, staying 1-2 inches away. Hold for 10-15 seconds, then turn the tip of iron toward the ground and release curl into palm of hand. Holding curl in one hand, gather up towards base and secure curl with a small metal clip (like a pin curl). Allow curl to cool completely, remove clip and let curl hang naturally. Hair can be combed with your wide tooth comb, or fingers.

Flat Iron- Heat your iron to around 275 degrees. Start at the nape in 1/2  to 1 1/2 inch sections, and spray Jon Renau Heat Treat Thermal Spray on the section to protect the fiber.Staying at least an inch away from the base, slowly smooth flat iron down through ends. Keep hair smooth by following behind the flat iron with your Jon Renau wide tooth comb. Allow hair to hang naturally and cool completely.

Ask your local wig store for this wig today!

 

Leave a Reply